Global water pollution is prevailing everywhere because of which installing a water softener is a necessity nowadays to improve the quality of water to carry out different applications. However, the real game is how to install a water softener; installing by yourselves might be daunting; finding any expert would cost much money, which becomes non-affordable. People have already spent much on the best water softeners, but if you get a step-by-step guide of installing a water softener, then it’s just like eating a pie. Let’s dive!
Salt-based water softener: How to install a water softener?
These are quite common among people, so we’re primarily going to discuss installing a salt-based water softener, before doing so kept all the codes of application of your area in your mind.
Gather tools for Installation
Following tools are necessary for installing a salt-based water softener:
- Gate valves
- Measuring tape
- Pipe cutter
- Pipe wrench
- Tee valves
- 2 compression fittings
- Teflon tape
- 2 union fittings
- Torch and solder
Gather materials for Installation
For appropriate Installation, you should have the following material:
- PVC solvent
- Flexible tubing
- Flux material (replacement of PVC solvent if unavailable)
- Simple tubing
Installing a salt-based water softener: Step-by-step guide
1. Shutdown mainlines
When you will shutdown the mainlines of water, open the bottom floor faucets, and drain out the other pipelines.
2. Shutdown water heater
To avoid any electric shock, shut down the water heater & main power supply (if you have installed) that runs with electricity or the gas hose.
3. Locate main water line
After this, locate the area in the mainline where you want to install a water softener, keep it closer to the main one for a faster flow rate.
4. Clean area
Sweep the area where you are going to place the water softeners, make sure the Inlet is attached to the pipeline and Outlet to the water heater (If you have).
5. Using pipe cutter
Now, with pipe cutter cut the area on mainline where a water softener is going to install, keep the bucket below because water may drain out when you will cut. Pay special attention to the orientation setting of Inlet and Outlet!
6. Install elbow fitting
Elbow fitting installation is essential at the mainline for the availability of the bypass valve.
7. Measure & attach pipes
Cut the large pipes after measuring up to the bypass valve using a reduce fitting for the correct size and then use compression fitting to connect them.
8. Clamp the hose
To avoid any water drainage, clamp the hose to the water softener very tightly and run it to drain to check, make sure it should be 2 inches above the utility sink.
9. Connect overflow tube
As per the user manual instructions with the water softener, follow them to adjust the height and connect the brine tank with the overflow tube.
10. Plugging
At last, make it start working by plugging into the unit. Open the valve slowly, release water in the unit first, and then to pipes. Partially open the Inlet to escape the air bubbles inside, once the water flows steadily and then move with adequate flow and fill the tank.
Magnetic water softener: How to install a water softener?
The second most commonly used one, which is much easy to install and require fewer things, have a look!
Gather tools
Following tools are necessary for installing a magnetic water softener:
- Wrench
- Screwdriver
Installing a magnetic water softener: a step-by-step guide
1. Locate area
These water softeners are compact in size and are easily fixable in any field.
2. Uncover softener
Take the softener out of the box with the user manual and read the provided steps and instructions carefully.
3. Pick tools
Now, fit the magnetic softener on the located area of Installation with the screwdriver and wrench.
4. Plugging
Plug the box with the electric supply so that softener can be easily installed on the pipeline.
Installing a water softener is not as much difficult as it seems to be, just follow up with an informative guides of how to install a water softener and you are quickly done with it. For salt-free water softeners installation and reverse osmosis system, it’s better to hire any technician, due to their difficulty level. We hope that you have found this article pretty good in installing the water softeners, for more information related to water quality testing kits and best water softeners visit us.